Page 1 of 1
Using PureBasic to Put the Hex Into ASM Code
Posted: Wed Sep 05, 2012 2:17 am
by oldefoxx
"Put the Hex into ASM Code"? Sounds strange, but let me show you what I mean
Here is the coded section:
Procedure.l tmp()
lablel1:
mov eax, 0xffffffff
label2:
add eax,1
label3:
ProcedureReturn
label4:
EndProcedure
MessageRequester("TRIAL","EAX = "+str$(tmp))
I get the result of 0, which is what I should get. But now I want the hex code involved
I want to use a pointer to label1 and pull up each byte in sequence until I get to label2,
then go from a pointer to label2 and do the same again for each byte until I reach
label3, then again from lable3 until I reach label4.
What I am trying to do is see when and where the prefix 66h comes into play. According
to what I've read, it should not appear. Then I am going to change the instructions to
involve ax instead of eax, When i repeat the scan from label1 to label3, I expect to find
two. I've a reason for wanting to know this for sure, which is why I'm looking for a bit of
help on using label pointers.
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Wed Sep 05, 2012 2:39 am
by jack
oldefoxx, have a look at
http://www.purebasic.fr/english/viewtop ... 13&t=51174
fasm dll comes with a demo that instantly assembles snippets of asm source giving you the machine code.
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Wed Sep 05, 2012 6:51 am
by wilbert
Code: Select all
Procedure.l tmp()
label1:
!mov eax, 0xffffffff
label2:
!add eax,1
label3:
ProcedureReturn
label4:
EndProcedure
s.s = ""
*addr.Ascii = ?label2
While *addr < ?label3
s + Hex(*addr\a) + " "
*addr + 1
Wend
MessageRequester("Output" , s)
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Thu Sep 06, 2012 1:33 am
by oldefoxx
Very nice. I had a suspicion about how it would be approached, but I was not "enough with the language"
to bring it together. I made a few small changes, to get the flavor I was looking for:
Code: Select all
Procedure.l tmp()
label1:
!mov eax, 0xffffffff
label2:
!add eax,1
label3:
ProcedureReturn
label4:
EndProcedure
s.s = "!mov eax, 0xffffffff ==> "
*addr.Ascii = ?label1
While *addr < ?label2
s + Hex(*addr\a) + " "
*addr + 1
Wend
s+Chr(13)+Chr(10)+"!add eax,1 ==> "
While *addr< ?label3
s+Hex(*addr\a)+" "
*addr+1
Wend
s+Chr(13)+Chr(10)+"ProcedureReturn (EAX) = "+Str(tmp)
MessageRequester("Output" , s)
But to verify that the process is going what is expected of it, I changed the value
being loaded into EAX at the start of the procedure. Now it reads like this:
Code: Select all
Procedure.l tmp()
label1:
!mov eax, 0x12345678
label2:
!add eax,1
label3:
ProcedureReturn
label4:
EndProcedure
s.s = "!mov eax, 0xffffffff ==> "
*addr.Ascii = ?label1
While *addr < ?label2
s + Hex(*addr\a) + " "
*addr + 1
Wend
s+Chr(13)+Chr(10)+"!add eax,1 ==> "
While *addr< ?label3
s+Hex(*addr\a)+" "
*addr+1
Wend
s+Chr(13)+Chr(10)+"ProcedureReturn (EAX) = "+Str(tmp)
MessageRequester("Output" , s)
No matter what value is assign to EAX at the start, the ProcedureReturn is always
equal to zero (0). Any idea why that is?
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Thu Sep 06, 2012 1:48 am
by Demivec
oldefoxx wrote:No matter what value is assign to EAX at the start, the ProcedureReturn is always
equal to zero (0). Any idea why that is?
It is because you never execute the procedure to get its return value, you only reference its contents (machine code) with the labels.
You should make this small change:
Code: Select all
;change this
s+Chr(13)+Chr(10)+"ProcedureReturn (EAX) = "+Str(tmp)
;to this
s+Chr(13)+Chr(10)+"ProcedureReturn (EAX) = "+Str(tmp())
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Thu Sep 06, 2012 2:08 am
by oldefoxx
Then I just learned something. tmp is not tmp(). Interesting. In some other languages,
if there is no parameters involved, the () is not required. An example that many people
might recognize where the () is required is the POS() in some of the early Basics, which
involves the current position on the line (column location). I also learned something
else, which is that while tmp is therefore undefined, it did not signal a compiler error.
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Thu Sep 06, 2012 2:19 am
by oldefoxx
Now this is interesting. I set the code back to 0xffffffff as I had it originally, and changed
Str() in the later part to Hex(), and got back an answere with 16 F's in it. Eight would have
been enough. Sixteen is like a quad, not a long.
Code: Select all
Procedure.l tmp()
label1:
!mov eax, 0xfffffffe
label2:
!add eax,1
label3:
ProcedureReturn
label4:
EndProcedure
s.s = "!mov eax, 0xffffffff ==> "
*addr.Ascii = ?label1
While *addr < ?label2
s + Hex(*addr\a) + " "
*addr + 1
Wend
s+Chr(13)+Chr(10)+"!add eax,1 ==> "
While *addr< ?label3
s+Hex(*addr\a)+" "
*addr+1
Wend
s+Chr(13)+Chr(10)+"ProcedureReturn (EAX) = "+Hex(tmp())
MessageRequester("Output" , s)
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Thu Sep 06, 2012 6:07 am
by Danilo
oldefoxx wrote:Now this is interesting. I set the code back to 0xffffffff as I had it originally, and changed
Str() in the later part to Hex(), and got back an answere with 16 F's in it. Eight would have
been enough. Sixteen is like a quad, not a long.
Use Hex(tmp(),#PB_Long).
Hex() takes a quad by default, so the .l 0xffffffff (it is -1, because PB uses signed types)
is converted to .q 0xffffffffffffffff (-1 for quads).
RSet is used to fill the string on the left side, so the byte display "1" becomes "01"
and long "FF" becomes "000000FF".
Variables do not need to be defined by default. Use EnableExplicit for enabling it.
Yes, procedures are always used with (), for example the address of the procedure is: @tmp().
Without () it is a simple variable.
Code: Select all
EnableExplicit
Procedure.l tmp()
label1:
!mov eax, 0xfffffffe
label2:
!add eax,1
label3:
ProcedureReturn
label4:
EndProcedure
Procedure.s GetByteCode( *_start.Ascii, *_end.Ascii, _msg.s="" )
While *_start < *_end
_msg + " " + RSet( Hex( *_start\a , #PB_Byte ) , 2, "0")
*_start + 1
Wend
ProcedureReturn _msg
EndProcedure
Define s.s
s = GetByteCode(?label1,?label2,"!mov eax, 0xfffffffe ==>")
s + #CRLF$
s + GetByteCode(?label2,?label3,"!add eax,1 ==>")
s + #CRLF$ + "ProcedureReturn (EAX) = " + RSet( Hex(tmp(),#PB_Long) , 8, "0" )
MessageRequester("Output" , s)
Re: Using PureBasic to Put the Hex Into ASM Code
Posted: Thu Sep 06, 2012 9:04 am
by oldefoxx
I appreciate your response. Stretches my understanding further. It's real late, and I
think I am done for the night. This has been a good thread to be part of.